Two components, two different jobs
The iVac Contactor and the iVac Pro Switch 240Vac are not interchangeable alternatives. They work together in an iVac Pro system, but each handles a different part of the control chain. The Pro Switch decides when to turn the dust collector on or off, while the Contactor handles the high current that large motors demand.
Your choice depends on your dust collector's motor tag, not on preference. The Contactor is required when current draw exceeds certain thresholds; the Pro Switch alone can manage smaller loads within its 20A rating.
What the iVac Contactor is built for
- iVac Contactor; 115Vac Trigger; 10HP Capacity: The iVAC Contactor is a heavy duty 3 pole relay housed in an electrical box, designed to switch high current surges to the dust collector. This relay design is what allows it to handle the startup current of large motors that would overwhelm a standard switch.

iVac Contactor; 115Vac Trigger; 10HP Capacity - iVac Contactor; 115Vac Trigger; 10HP Capacity: It can withstand start up currents of up to 150 Amps and maintain a running current of up to 40 Amps. These ratings determine whether your dust collector's motor falls within the Contactor's capacity.
- iVac Contactor; 115Vac Trigger; 10HP Capacity: The contacts are rated to operate at up to 240Vac, either single or three phase, enabling it to handle 1.5HP dust collectors at 115Vac and up to 10HP at 230Vac 3 phase. This confirms the Contactor's role for larger motors and higher voltage systems, including three-phase setups.
What the iVac Pro Switch 240Vac controls
- iVac Pro Switch; 240Vac; 20A: The iVAC Pro Switch modules are used to automatically turn on your Dust Collector or Shop Vac when you turn on a power tool plugged into an iVAC Pro Tool module. This is the tool-triggered automation function that many woodworkers want for convenience and safety.

iVac Pro Switch; 240Vac; 20A - iVac Pro Switch; 240Vac; 20A: Current capacity is 20Amps and the circuit breaker is rated at 20Amps. This 20A limit defines the maximum load the Pro Switch can handle directly without a Contactor.
- iVac Pro Switch; 240Vac; 20A: Typical motor drive capability is 2HP at 240Vac. This gives a practical reference for the size of dust collector the Pro Switch can manage on its own.
When you need the Contactor
The iVac documentation provides clear thresholds. You MUST use a contactor if your dust collector draws more than 9 amps at 115VAC or 8 amps at 240VAC. Additionally, the manufacturer strongly recommends the Contactor for dust collectors operating on 115Vac rated over 1HP and for any dust collector over 1.5HP operating on 230Vac.
In practice, this means the Pro Switch alone is suitable only for smaller dust collectors or shop vacs that stay below these limits. For larger machines, the Contactor is not optional—it is required to safely handle the current.
Voltage and triggering: a critical detail
Even if your dust collector runs on 230Vac, the Contactor must be triggered with 115Vac. This means the correct iVac Switch unit must be used to provide that 115Vac trigger signal. The Pro Switch 240Vac is designed for 240Vac operation, so it cannot serve as the trigger for a Contactor in a 230Vac system.
This voltage mismatch is a common pitfall. Always verify the trigger voltage required by the Contactor and match it to your switch unit.
Key differences at a glance
- Primary function: Contactor: heavy-duty relay for high-current switching. Pro Switch: automated on/off control with tool-triggered operation.
- Current capacity: Contactor: 40A running, 150A startup. Pro Switch: 20A maximum.
- Voltage: Contactor: up to 240Vac, single or three phase. Pro Switch: 240Vac.
- Motor size capability: Contactor: up to 10HP at 230Vac 3 phase. Pro Switch: 2HP at 240Vac typical.
- Trigger voltage: Contactor: requires 115Vac trigger. Pro Switch: operates at 240Vac.
- Installation: Contactor: must be installed by a licensed electrician. Pro Switch: plug-in module with NEMA receptacles.
How they work together
In a complete iVac Pro system, the Pro Switch receives the signal from a tool module and controls the Contactor, which in turn switches the dust collector. The Contactor is designed to work with the iVac Switch Box or an iVac Pro Switch 115-102S. Note that the Pro Switch 240Vac (model 1288469) is not listed as a compatible controller for the Contactor; the 115-102S is the specified unit.
This means you cannot simply pair the Pro Switch 240Vac with the Contactor. If you need a Contactor, you must use the correct switch unit that provides the 115Vac trigger.
Making the decision
Start by reading your dust collector's motor tag. If it draws more than 9A at 115VAC or 8A at 240VAC, or if it exceeds 1HP at 115Vac or 1.5HP at 230Vac, you need the Contactor. In that case, you also need a compatible switch unit (iVac Switch Box or Pro Switch 115-102S) to trigger it.
If your dust collector is smaller and within the Pro Switch's 20A and 2HP limits, the Pro Switch 240Vac can handle automation directly. However, note that the Pro Switch 240Vac is a 240Vac device; for 115Vac systems, a different Pro Switch model would be required.
Always confirm compatibility with the manufacturer's documentation and consult a licensed electrician for Contactor installation.


